Jump to content
Sign in to follow this  
TonyHzNV

Radio went off unexpectedly

Recommended Posts

Yesterday I was driving home from work and I was listening to 100.5, one of the presets on FM1. Suddenly there was no sound and I figured the station had a momentary loss of signal, so I tried switching to another station to check. There was no response to my input on the touchscreen so I tried switching to SiriusXM...nothing. Tried switching to CD and again, no response. I tried switching to FM2, no response. I reached into my center console and got my USB reboot stick and plugged it in. MFT did it's thing and at the next red light, I shut off the car and opened the door so it would reboot and everything came back to normal. Has anyone else seen this? That's like the 3rd time I've had to reboot MFT in the 7-1/2 Mos. I've had the car each time for a different reason. Glad I made that USB stick!

Edited by TonyHzNV

Share this post


Link to post
Share on other sites

I've had my MFT sound lock up similarly, but it usually comes back alive for me after about 5-30 seconds.

Share this post


Link to post
Share on other sites

This was more than losing the sound though. The buttons on the screen were dead no matter what I touched.

Share this post


Link to post
Share on other sites

Yep, happens to me also. I have narrowed it down to an OBD 2 bluetooth adapter, bluetooth itself or high voltage.

 

I replaced the OBD adapter with an Ultra Gauge. I hope that eliminates one variable.

 

Im seeing voltages over 15 alot. The service manual says 15.5 is the limit, but there could be spikes that my voltage checker just cant pick up.

 

Hasnt done it in a month or so.

 

Also, mine just reboots on its own.

Edited by Griswald

Share this post


Link to post
Share on other sites

Counting myself lucky, the only time sound stops is when listening to Pandora over USB to my iphone, and its the damned Iphone that does it. I have a speaker dock charging station that it does the same thing to so I know it isn't MFT.

 

Have you guys had the FCIM update done yet? If not, you may want to have it done, it could be the module acting up. (I think its FCIM, others can correct me if wrong).

Share this post


Link to post
Share on other sites

I don't know what the FCIM UPDATE is, but nothing shows up as outstanding on my OASIS report.

Share this post


Link to post
Share on other sites

It wont. Its under a TSB. Its an update for the buttons on the center stack. You can easily tell if its had it done by setting your HVAC to auto, going to my view and put up the energy use on the right side, the one with two horizontal bar graphs. The top on will show AC compressor use. turning off the AC while in auto, if you still see energy used on the top one, your's hasn't been updated. It covered a wide variety of issues beside the AC not really being turned off.

 

 

 

http://fordfusionhybridforum.com/topic/6852-tsb-14-0096-reprogram-the-front-controls-interface-module/

Edited by acdii

Share this post


Link to post
Share on other sites

OK thanks for the info. I'll check into it.

 

Edit: After reading the updated TSB here: http://fordfusionhybridforum.com/topic/6852-tsb-14-0096-reprogram-the-front-controls-interface-module/?p=87217 it doesn't appear it applies to my vehicle. Mine was built on 11/25/13, doesn't have remote start and DOES have dual zone automatic temperature control.

Edited by TonyHzNV

Share this post


Link to post
Share on other sites

This was more than losing the sound though. The buttons on the screen were dead no matter what I touched.

 

I typically only use the steering wheel buttons to control the entertainment. But when my sound, typically XM, locks up, I can't change stations at all using the steering wheel buttons. So for me, when the XM locks up occasionally, it seems that at a minimum the whole entertainment section portion is locked up. I haven't really tried controlling anything else during those lockup periods to see if other portions are locked up too.

Share this post


Link to post
Share on other sites

Thats a module control issue. Probably needs an update, or replacement.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

×
×
  • Create New...